-
1,207.23€ (2,361.13лв)
- Ex Tax: 1,006.02€ (1,967.61лв)
| Chargers | |
| Charge current | 70 A |
| Charger AC Input | 187-265 VAC Input frequency: 45 – 65 Hz |
| Hybrid inverters | |
| Cont. output power at 25°C (W) | 1300 W |
| Input voltage range (V DC) | 9,5 – 17 V |
| Max efficiency (%) | 93 |
| Output AC voltage/frequency | 230 VAC ± 2% 50 Hz ± 0,1% |
| Peak Power (W) | 3000 W |
| Protection | - output short circuit - overload - battery voltage too high - battery voltage too low - temperature too high - 230 V AC on inverter output - input voltage ripple too high |
| Transfer switch (A) | 16 |
| Zero load power (W) | 8 |
Two AC Outputs
The main output has no break functionality. The MultiPlus
takes over the supply to the connected loads in the event of a grid failure or
when shore/generator power is disconnected. This happens so fast (less than 20
milliseconds) that computers and other electronic equipment will continue to
operate without disruption. The second output is live only when AC is available
on one of the inputs of the MultiPlus. Loads that should not discharge the
battery, like a water heater for example can be connected to this output
(second output available on models rated at 3 kVA and more).
Virtually unlimited power thanks to parallel operation
Up to 6 Multis can operate in parallel to achieve higher
power output. Six 24/5000/120 units, for example, will provide 25 kW / 30 kVA
output power with 720 Amps charging capacity.
Three phase capability
In addition to
parallel connection, three units of the same model can be configured for three
phase output. But that’s not all: up to 6 sets of three units can be parallel
connected for a huge 75 kW / 90 kVA inverter and more than 2000 Amps charging
capacity.
PowerControl - Dealing with limited generator, shore side or
grid power
The MultiPlus is a very powerful battery charger. It will
therefore draw a lot of current from the generator or shore side supply (nearly
10 A per 5 kVA Multi at 230 VAC). With the Multi Control Panel a maximum generator
or shore current can be set. The MultiPlus will then take account of other AC
loads and use whatever is extra for charging, thus preventing the generator or
shore supply from being overloaded.
PowerAssist - Boosting the capacity of shore or generator
power
This feature takes the principle of PowerControl to a
further dimension. It allows the MultiPlus to supplement the capacity of the
alternative source. Where peak power is so often required only for a limited
period, the MultiPlus will make sure that insufficient shore or generator power
is immediately compensated for by power from the battery. When the load
reduces, the spare power is used to recharge the battery.
Solar energy: AC power available even during a grid failure
The MultiPlus can be used in off grid as well as grid
connected PV and other alternative energy systems. Loss of mains detection
software is available.
System configuring
- In case of a
stand-alone application, if settings have to be changed, this can be done in a
matter of minutes with a DIP switch setting procedure.
- Parallel and three
phase applications can be configured with VE.Bus Quick Configure and VE.Bus
System Configurator software.
- Off grid, grid
interactive and self-consumption applications, involving grid-tie inverters
and/or MPPT Solar Chargers can be configured with Assistants (dedicated
software for specific applications).
On-site Monitoring and control
Several options are available: Battery Monitor, Multi
Control Panel, Ve.Net Blue Power Panel, Color Control Panel, smartphone or
tablet (Bluetooth Smart), laptop or computer (USB or RS232).
Remote Monitoring and control
Victron Ethernet Remote, Victron Global Remote and the Color
Control Panel. Data can be stored and displayed on our VRM (Victron Remote
Management) website, free of charge.
Remote configuring
When connected to the
Ethernet, systems with a Color Control panel can be accessed remotely and
settings can be changed.