-
2,985.09€ (5,838.32лв)
- Ex Tax: 2,487.57€ (4,865.27лв)
| Chargers | |
| Charge current | 70 A |
| Hybrid inverters | |
| Cont. output power at 25°C (W) | 4000 W |
| Input voltage range (V DC) | 38 – 66V |
| Max efficiency (%) | 95% |
| Output AC voltage/frequency | 230 VAC ± 2% 50 Hz ± 0,1% |
| Peak Power (W) | 10 000 W |
| Protection | - output short circuit - overload - battery voltage too high - battery voltage too low - temperature too high - 230 VAC on inverter output - input voltage ripple too high |
| Transfer switch (A) | yes, integrated |
| Zero load power (W) | 35 |
Two AC inputs with
integrated transfer switch
The Quattro can be connected to two independent AC sources,
for example the public grid and a generator, or two generators. The Quattro
will automatically connect to the active source.
Two AC Outputs
The main output has
no-break functionality. The Quattro takes over the supply to the connected
loads in the event of a grid failure or when shore/generator power is
disconnected. This happens so fast (less than 20 milliseconds) that computers
and other electronic equipment will continue to operate without disruption. The
second output is live only when AC is available on one of the inputs of the
Quattro. Loads that should not discharge the battery, like a water heater for
example, can be connected to this output.
Virtually unlimited
power thanks to parallel operation
Up to 6 Quattro units can operate in parallel. Six units
48/10000/140, for example, will provide 54kW / 60kVA output power and 840 Amps
charging capacity.
Three phase
capability
Three units can be configured for three phase output. But
that’s not all: up to 6 sets of three units can be parallel connected to
provide 162kW / 180kVA inverter power and more than 2500A charging capacity.
PowerControl –
Dealing with limited generator, shore side or grid power
The Quattro is a very powerful battery charger. It will
therefore draw a lot of current from the generator or shore side supply (16A
per 5kVA Quattro at 230VAC). A current limit can be set on each AC input. The
Quattro will then take account of other AC loads and use whatever is spare for
charging, thus preventing the generator or mains supply from being overloaded.
PowerAssist –
Boosting shore or generator power
This feature takes the principle of PowerControl to a
further dimension allowing the Quattro to supplement the capacity of the
alternative source. Where peak power is so often required only for a limited
period, the Quattro will make sure that insufficient mains or generator power
is immediately compensated for by power from the battery. When the load
reduces, the spare power is used to recharge the battery.
Solar energy: AC
power available even during a grid failure
The Quattro can be used in off grid as well as grid
connected PV and other alternative energy systems. Loss of mains detection
software is available.
System configuring
- In case of a
stand-alone application, if settings have to be changed, this can be done in a
matter of minutes with a DIP switch setting procedure.
- Parallel and three phase applications can be configured with
VE.Bus Quick Configure and VE.Bus System Configurator software.
- Off grid, grid interactive and self-consumption
applications, involving grid-tie inverters and/or MPPT Solar Chargers can be
configured with Assistants (dedicated software for specific applications).
On-site Monitoring
and control
Several options are available: Battery Monitor, Multi
Control Panel, Ve.Net Blue Power panel, Color Control panel, smartphone or
tablet (Bluetooth Smart), laptop or computer (USB or RS232).
Remote Monitoring and control
Victron Ethernet Remote, Victron Global Remote and the Color
Control Panel. Data can be stored and displayed on our VRM (Victron Remote
Management) website, free of charge.
Remote configuring
When connected to the Ethernet, systems with a Color Control panel can be accessed and settings can be changed.